Rock Products - The Leading Voice of the Aggregate Industries.

Boart Longyear Rock Drill Passes the Test

37 DB 400While many underground mines are looking to avoid handheld rock drills for the safety of the miners, there are still many mines in North America where jackleg drilling is a must.

For these narrow-vein mines, located primarily in Eastern Canada and throughout Mexico, cabbed jumbos, bolters and long-hole rigs are not feasible due to cost and size restraints. Instead the operation teams still depend on handheld rock drills, a technology that has changed relatively little in more than 70 years.

Starting in 2010, however, the Boart Longyear engineering team took a hard look at the design of these drills, including their own Secan S-250. The goal was to reduce the noise level and amount of vibration the drill puts out. The outcome was a new top-of-the-line handheld rock drill – the S250-M3 – which instantly made jackleg drilling a much safer operation.

Introduced in early 2013 to a very receptive market, the S250-M3 represents a major step forward in rock drilling. Reflecting Boart Longyear’s commitment to making a truly better and safer drill, it significantly improved upon the industry-standard Secan S-250 by introducing advanced noise suppression.

The new technology directs more energy to the face of the rock and less into the body of the driller. Independent tests showed the S250-M3 reduces the noise level by 6 decibels – resulting in half the noise – while increasing torque and penetration rates. In fact, one driller commented that it was the first time he could feel his feet and hands after a full shift using a rock drill.

Subsequently, an independent, third-party comparison test at an underground site in the western U.S. put the S250-M3 and three other leading jacklegs head-to-head. As a result of this testing under actual mine conditions, Boart Longyear’s S250-M3 emerged as the evaluation team’s drill of choice for rock drilling at the site.

Comparison Test

The PHQ 250 JHSL Pneumatic Jackleg was already being used for the installation of ground support at the site where the comparison testing took place. While a hydraulic rock bolting jumbo had been purchased to help reduce risk to drillers, management determined that handheld drills would still be required in the shafts. Therefore, they wanted to consider alternative products that were reported to reduce exposure to sound and vibration hazards.

Selected for testing were the PHQ250 JHSL, the PHQ250 JHNAVL (a variant with an antivibration buffer on the handle), the Boart Longyear S250-M3 and one electric drill, the Hilti TE MD20 Electric Jackleg.

38 DB 400Representatives from the various drill suppliers were on hand but did not participate directly in the independent testing, which utilized the services of four drillers over a period of four consecutive shifts over two days. Performance data was collected to determine sound production (dBA), vibration (m/s²) and penetration rate.

A 185-cfm diesel compressor was used for compressed air, and each drill and leg was connected to the same 100-ft. length of 1½-in. diameter air hose to ensure that a consistent volume and pressure of compressed air would be provided to each drill. Air pressure was measured at the drill and recorded for each test.

Water for drilling was taken from a 2-in., high-pressure industrial water line with water pressure reduced from approximately 350 to 75 psi with a pressure reducer. Electricity was provided from an existing service at 220 volts.

Each machine was used to drill three holes, varying between 1 3/8 and 1 1/4 in. in diameter and up to 6 ft. deep. Because the Hilti drill did not have a drill string longer than 2 ft., that was the maximum length of the holes that could be drilled with that particular drill.

Consistent Rock Mass

To ensure that all holes would be drilled in a consistent rock mass, they were all drilled in the same general area. This location also provided for the hardest drilling that would be encountered to provide a worst-case scenario for penetration rates.

Each set of holes was drilled with a new bit, and each pneumatic drill used the same leg so any variations in leg operation would not impact the penetration rates.

Sound measurements, using a handheld sound level meter and a dosimeter, were taken near the driller’s ear. A Quest Technologies 2100 Sound Level Meter (SLM) was used to measure sound pressure levels.

Vibration was measured using an accelerometer that was taped to the drill handle while each driller wore a monitor on his bib overalls.

After each set of holes was drilled, 6-ft. resin anchored rockbolts were installed in each hole drilled by the pneumatic drills but not in the shorter holes drilled with the Hilti drill. The time to complete this installation was measured.

Not surprisingly, Hilti’s electric drill produced the lowest average sound level values of all the drills tested – 101.5 dBa. Of the pneumatic machines, Boart Longyear’s drill produced both the lowest average sound level values, 109.5 dBa – well below the 116.5 dBa average of the older PHQ drill being used at the site and even below the 113 dBa average of the newer PHQ model.

Similarly, the electric Hilti drill produced the lowest vibration results of all the drills tested and the Boart Longyear produced the lowest vibration results of all the pneumatic machines.

As for penetration, the three pneumatic machines were fairly consistent at 1.5 to 1.7 ft. per minute, with the S250-M3 posting a slightly higher average penetration rate than the PHQ drills. The electric Hilti drill, however, lagged with a penetration rate of about one-third those of the pneumatic drills.

In addition to the recorded performance data, each driller provided evaluations regarding his personal observations of the operation of each drill, including overall ease, noise and vibration.

Boart Longyear S250-M3 Results in Third-Party Testing
  • Lowest sound production – 109.5 dba
  • Lowest vibration – 20 m/s2
  • Highest penetration rate – 1.7 ft./min
  • Highest overall ease of use rating – 18.56 (25 possible)
  • Highest noise/vibration perception – 7.44 (10 possible)
  • Highest overall score – 26 (35 possible)

So what did they think of the various drills they tested? Asked to score various criteria on a five-point scale, the miners ranked the S250-M3 highest overall with 26 points out of a possible 35, and highest for overall ease of use with 18.56 points out of 25. The electric Hilti ranked first for overall noise/vibration with 8 out of a possible 10 points and the Boart Longyear drill close behind with 7.44 points.

The evaluation team noted that despite the electric Hilti’s advantage in terms of sound and vibration rates, its dramatically lower penetration rate compared with the pneumatic drills made it unsuitable for their applications. Subsequently, they also learned that Hilti would no longer market the TE MD20 drill in North America, altogether eliminating it from consideration. As a result of the head-to-head testing of the remaining drills – all pneumatic machines – the evaluation team recommended the S250-M3 as its drill of choice for rock drilling.

The S250-M3 comes in three primary variations to match specific customer needs – jackleg, stopper and sinker. The drill hex chuck ends are available in both 22 mm and 25 mm.

Jared Kessen is senior business development manager – Percussive Products (North America) for Boart Longyear.